What Are The Common Types Of Communication Problems In The Fire Service

What Does the Burn down Alert Panel Indicate Mean?

Do you get a feeling of dread when you just run across a seedling lit on your fire alert console? The first stride to making you experience more comfy with your burn warning panel is to understand what basic fire alarm panel signals mean. The three almost bones burn down alarm console signals are problem, supervisory, and alarm. If yous work in facilities management or maintenance it's extremely helpful for you to understand what signals look similar on most systems, common causes of activations, and how to solve the problem. Here's an explanation of what each fire alarm panel indicate means.

Fire Alarm Trouble Signal

A fire warning trouble signal is generally xanthous and indicates in that location's an operational effect. Some fire warning panels may betoken the type of fire alert trouble and its location. Hither are some of the common reasons for a problem bespeak.

Fire Alarm Batteries

Check fire alarm batteries connections and remaining capacity. They may fall below the rated capacity if they haven't been changed in 3-5 years.

Power

Does the fire alarm system have power? Verify the electrical breaker hasn't been inadvertently shut off. This is often overlooked.

Ground Error

There are a few situations that produce ground faults. A bare wire in the back of a fire alarm device could be touching the junction box. In that location may be open circuits or a wire could have gotten loose or come up completely off a device. If in that location was a storm in the area, then a lightning strike could have produced issues with the circuits. In these cases, call your service provider to investigate the consequence.

Copper Line to Voice Over IP

A more recent result is due to facilities switching from copper lines to voice-over IP. When they forget about the burn down alarm during the change, it remains connected to the inactive copper line and tin can't complete its daily test. Additionally, it won't be able to dial out in the instance of an emergency. If yous doubtable this issue caused the trouble indicate, phone call your burn protection service provider. Ask them whether the burn alert system is compatible with vocalism-over IP engineering. In some cases, fire alert systems may accept to retain their copper line.

Burn down Alarm Supervisory Signal

A burn down alert supervisory point is typically yellow and indicates there'southward an issue with some other system that'due south attached and monitored by the fire alert system.

Sprinkler Valve/Tamper Switch Active

Technicians sometimes forget to leave fire sprinkler valves open after service. An in-house maintenance team should exist able to properly accommodate the valve.

Low-Pressure Switch on Dry Pipe Arrangement

Cheque to make sure your compressor hasn't stopped and that it's running properly. In some cases, the compressor can't see the fire sprinkler system's pressure demand. This could occur when at that place's a small hole in the pipe that allows air to escape. In the winter, pipes may freeze and split. When the weather warms upward, the ice melts allowing air to escape through the damaged pipe. A burn protection contractor needs to accost this issue.

Duct Detector

Turning on an air conditioning or heating organization at the start of the flavor tin can actuate duct detectors. When the ac is operating, it could produce loftier humidity and condensation. In the winter, grit that collects on heating coils starts to burn and produces fume. Both conditions could cause duct detectors to become off and produce a supervisory signal. Notify your fire protection company nearly the issue. Additionally, clean your filters and duct detectors regularly.

Alarm Bespeak

A crimson fire warning bespeak indicates there's an emergency that requires immediate attending. These are the almost common reasons for false alarms.

Improper Fire Alert Maintenance

Is your fire alarm organization serviced at the proper intervals?

Fume Detectors

Unfortunately, it's very common for facility personnel to improperly clean smoke detectors. Always have fume detectors cleaned per the manufacturer'southward specifications.

Waterflow Switches

Improperly set retard/delay mechanism on the waterflow switch. This tin cause it to produce a false alarm when a surge of water flows through it. The retard or check valve could also exist bad and require replacement.

Malicious Activations

People maliciously activating fire alarm pull stations is a serious trouble considering information technology weakens occupants' trust in the system. To deter fake activations, install pull station covers.

Download the Quick Reference Guide to Burn down Alarm Panel Signals Meaning on the left and post it in your fire alarm console. Then the side by side time your burn alarm system produces a signal, yous'll have a meliorate understanding of the problem and how to solve it.

Categorized in: Fire Alarms, General